Metafor

ULiege - Aerospace & Mechanical Engineering

User Tools

Site Tools


doc:user:geometry:mesh:2d

This is an old revision of the document!


2D Meshers (Surfaces)

Metafor has a few integrated meshers, quite simple but usually capable of meshing parts that are not too complicated. However, 2D meshers require that the wire delimiting the domain has the right orientation. The wire must be defined with its “area to the left”, which means that when the wire is followed along its orientation (defined by the succession of its curves), the matter of the part is on the left-hand

Contour "aire à gauche"

Transfinite mesher

With auto-detection

The auto-detection is working if the Sides is made of 4 edges, each of which is only made of one Curve.

TransfiniteMesher2D(sideset(number)).execute(type, tri)
number = number of the Side to mesh
type = True if mesh elements must be generated
= False if only nodes must be generated (useful in 3D!)
tri = 0 to generate quads (CELL_QUAD) [default]
= 1 to generate triangles from the first node (CELL_TRIANGLE)
= 2 to generate triangles from the second node (CELL_TRIANGLE)

Maillage possible avec autodétection

In the example above, the auto-detection is doable.

A similar function for higher degrees is:

HighDegreeTransfiniteMesher2D(sideset(number), degree).execute(type, sideNode, tri)
number = number of the side Side
degree = mesh degree (2 or 3)
type = True if mesh elements must be generated
= False if only nodes must be generated (useful in 3D!)
sideNode = True to generate 9-nodes mesh elements (CELL_NINE_QUADRATIC_QUAD)
= False to generate 8-nodes mesh elements (CELL_QUADRATIC_QUAD)
tri = 0 to generate quads (CELL_QUAD) [default]
= 1 to generate triangles from the first node (CELL_TRIANGLE)
= 2 to generate triangles from the second node (CELL_TRIANGLE)

For 9-nodes mesh elements, the central node is linked to the Side.
For 16-nodes mesh elements, central nodes are linked to the Side.

Without auto-detection

  mat = ((mat11, mat12, ..., mat1nbmax), 
         (mat21, mat22, ..., mat2nbmax), 
         (mat31, mat32, ..., mat3nbmax), 
         (mat41, mat42, ..., mat4nbmax)   )
  TransfiniteMesher2D(sideset(number)).execute2(mat, type)

where mat is a python tuple with 4 components. Each component is a tuple which contains the number of the curves which constitute each edge. Each of these four edges can be made of a different number of curves.

Example:

Maillage sans autodétection

This face can be meshed by the command:

 TransfiniteMesher2D(sideset(1)).execute2( (1,2,(3,4),5) )

The order of the lines does not matter in 2D (in opposition to the 3D case). Therefore, the following command also works:

 TransfiniteMesher2D(sideset(1)).execute2( ((4,3),1,2,5) )

Transfinite mesher on a side

The mesh can be projected on the surface surfNo (whether with or without auto-detection) if this surface is associated to the Side before the meshing operation:

 sideset(1).setSurfaceNo(surfNo)
 

2D transfinite mesher with a non-uniform mesh elements distribution

This is done with the commands:

MesherTFI2D =TransfiniteMesher2D(sideset(number))
MesherTFI2D.setEnableDistribution()
MesherTFI2D.execute(type, tri) or MesherTFI2D.execute2(mat, type)        

when one if the edges is already discretized using a mesh elements distribution.

Note : By default, the parameter of the function setEnableDistribution is set to True.

Frontal mesher

Description

Expert!Danger! This mesher is a new implementation of L. Stainer's work, which contains an offset and frontal mesher. It is usually rather disappointing.

Use

Triangles (frontal):

sidset(no).frontalTriangle(d)

Quadrangles (offset + frontal):

sidset(no).frontalQuad(d)

where d is the average length of the mesh elements edges to generate.

Gen4 mesher

Description

This quadrangular mesher is based on Sarrate algorithm. This method consists in diving the domain in a recursive way until only one quadrangle remains. It is very robust, and enables efficient meshing of complex domains.

By design, running twice Gen4 with the exact same parameters does not necessary lead to the same mesh. This can lead to some issues when running a simulation on a computer and trying to load results on another. To avoid this, the mesh generated is saved in a “.gen4” file, which will be read when loading a fac instead of creating the mesh anew. This “.gen4” file is not automatically deleted when cleaning the worskpace, so if you modify your mesh parameters, you must manually delete this file.

Possibilities

Gen4 can be used to mesh:

  • any planar face (convex or not, with or without holes)
  • including density (linear interpolation between two values specified on the vertices of the face).
  • including the “background mesh” type (density specified on a secondary mesh).
  • with integrated smoothing
  • with topological correction

Use

These lines are used to mesh the face #1 of the domain, whose vertices (points #1, #2, #3 and #4) densities are 0.1, 0.1, 0.2 and 0.05.

from toolbox.meshers import Gen4Mesher
defaultDensity = 0.1
mesher = Gen4Mesher(sideset(1), domain, defaultDensity)
mesher.setPointD(3,0.2)
mesher.setPointD(4,0.05)
mesher.execute() 

A default density, used unless explicitly stated differently, can be defined. This way, a density is only defined on specific mesh points. If no value is assigned in the data set, $0.1$ is taken as default density value.

CAREFUL : The face #1 must be defined in the XY plane.

 Exemple de maillage avec Gen4

Triangular mesher

Description

Create triangles on a planar face, as a function of

  • the maximal area of the triangle
  • the maximal angle of the triangle

Use

See, for example, the case apps.qs.triangleMesher. After creatin a face Side(1), it was meshed with a maximal area of 0.05 as criterion.

from toolbox.meshers import TriangleMesher
mesher = TriangleMesher(sideset(1), domain)
#mesher.setMaxAngle(20)
mesher.setMaxArea(0.05)
mesher.execute()

 Exemple de maillage triangulaire

doc/user/geometry/mesh/2d.1459344184.txt.gz · Last modified: 2016/07/11 16:04 (external edit)

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki