Metafor

ULiege - Aerospace & Mechanical Engineering

User Tools

Site Tools


doc:user:geometry:user:courbes

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision
Previous revision
Last revisionBoth sides next revision
doc:user:geometry:user:courbes [2015/01/07 17:31] – [Open cubic spline] bomandoc:user:geometry:user:courbes [2015/01/26 12:13] joris
Line 10: Line 10:
 {{ doc:user:doc-courbe.png?300 |}} {{ doc:user:doc-courbe.png?300 |}}
  
-===== Line: straight segment =====+===== Line: Straight Segment =====
  
-{{ doc:user:doc-droite.png|}}+{{ doc:user:doc-droite.png |}}
  
 A ''Line'' (line segment) is defined with its two vertices. A ''Line'' (line segment) is defined with its two vertices.
Line 22: Line 22:
 | ''pt1'',''pt2''     | the 2 ''Points'' used as vertices              | | ''pt1'',''pt2''     | the 2 ''Points'' used as vertices              |
  
-===== Arc ===== +===== Arc: Arc of Circle ===== 
  
-{{ doc:user:doc-arc.png|}}+{{ doc:user:doc-arc.png |}}
  
 An ''Arc'' of circle is defined using three points, as shown on the figure. An ''Arc'' of circle is defined using three points, as shown on the figure.
Line 37: Line 37:
 ===== Cubic Spline ===== ===== Cubic Spline =====
  
-{{ doc:user:doc-spline.png|}}+{{ doc:user:doc-spline.png |}}
  
 ==== "Open" Cubic Spline ==== ==== "Open" Cubic Spline ====
  
   spl = curveset.add( CubicSpline(number, [pt1, pt2, pt3, pt4]) )    spl = curveset.add( CubicSpline(number, [pt1, pt2, pt3, pt4]) )
-  spl.useLsTangent()    # tangents are calculated +  spl.useLsTangent()    # tangents are computed 
                         # using local reconstruction [DEFAULT]                         # using local reconstruction [DEFAULT]
-  spl.useLittTangents() # tangents are calculated +  spl.useLittTangents() # tangents are computed 
                         # using Litt/Beckers lectures                         # using Litt/Beckers lectures
                                              
Line 66: Line 66:
 where ''obj'' is a meshed object. where ''obj'' is a meshed object.
  
-===== Full Circle ===== +===== Circle: Full Circle ===== 
  
-{{ doc:user:doc-cercle.png|}}+{{ doc:user:doc-cercle.png |}}
  
 A circle is defined with its center and radius (this function is only defined in the $z=0$ plane) A circle is defined with its center and radius (this function is only defined in the $z=0$ plane)
Line 88: Line 88:
 A Non-Uniform Rational Basis Spline (N.U.R.B.S.) is defined as: A Non-Uniform Rational Basis Spline (N.U.R.B.S.) is defined as:
  
-{{ doc:user:doc-nurbs.png|}}+{{ doc:user:doc-nurbs.png |}}
  
   nur = curset.add( NurbsCurve(number) )   nur = curset.add( NurbsCurve(number) )
doc/user/geometry/user/courbes.txt · Last modified: 2016/03/30 15:23 by 127.0.0.1

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki