Metafor

ULiege - Aerospace & Mechanical Engineering

User Tools

Site Tools


doc:user:elements:volumes:iso_hypo_materials

Traditional Materials

The orthotropic frame is a reference frame which is tied to the matter. It can be used to get stresses in a frame which is initially along given directions (for example, axial stresses on a sheet metal), or for anisotropic reasons. By default, the fame is aligned on the global one.

TODO : Explain objectity.

ElastHypoMaterial

Description

Basic elastic law.

Parameters

Name Metafor Code Dependency
Density MASS_DENSITY
Young's modulus ELASTIC_MODULUS
Poisson Ratio POISSON_RATIO
Material Stiffness
(STIFF_ANALYTIC - STIFF_NUMERIC)
only if element Stiffness == STIFF_ANALYTIC
MATERIALSTIFFMETHOD -
Objectivity Method
(Jaumann = 0, GreenNaghdi = 1)
OBJECTIVITY -
Orthotropic axis ORTHO_AX1_X -
Orthotropic axis ORTHO_AX1_Y -
Orthotropic axis ORTHO_AX1_Z -
Orthotropic axis ORTHO_AX2_X -
Orthotropic axis ORTHO_AX2_Y -
Orthotropic axis ORTHO_AX2_Z -

TmElastHypoMaterial

Description

Basic thermoelastic law

Parameters

Name Metafor Code Dependency
Density MASS_DENSITY
Young's modulus ELASTIC_MODULUS
Poisson ratio POISSON_RATIO
Material Stiffness
(STIFF_ANALYTIC - STIFF_NUMERIC)
only if element Stiffness == STIFF_ANALYTIC
MATERIALSTIFFMETHOD -
Objectivity method
(Jaumann = 0, GreenNaghdi = 1)
OBJECTIVITY -
Orthotropic axis ORTHO_AX1_X -
Orthotropic axis ORTHO_AX1_Y -
Orthotropic axis ORTHO_AX1_Z -
Orthotropic axis ORTHO_AX2_X -
Orthotropic axis ORTHO_AX2_Y -
Orthotropic axis ORTHO_AX2_Z -
Thermal expansion THERM_EXPANSION TO/TM
Conductivity CONDUCTIVITY TO/TM
Heat capacity HEAT_CAPACITY TO/TM
Dissipated thermoelastic power fraction DISSIP_TE -
Dissipated (visco)plastic power fraction (Taylor-Quinney factor) DISSIP_TQ -

KelvinVoigtViscoElastHypoMaterial

Description

The Kelvin-Voigt viscoelastic law result in adding a viscous effect on the elastic material. The similar spring/damper model is shown at the figure below

The effect of viscosity is only impacting deviatoric stresses (all computations done on a finite time step $\Delta t$)

$$ \begin{cases} p^{1} = p^{0} + 3K {\Delta\epsilon}_{ii} \\ s^{1}_{ij} = s^{0}_{ij} + 2G {\Delta\hat{\epsilon}}_{ij} + \eta \frac{{\Delta\hat{\epsilon}}_{ij}}{\Delta t} \end{cases} $$

where $K$ and $G$ are compressibility and shear modulus.

Parameters

Name Metafor Code Dependency
Density MASS_DENSITY -
Young's modulus ELASTIC_MODULUS TO/TM
Poisson Ratio POISSON_RATIO TO/TM
Material Stiffness
(STIFF_ANALYTIC - STIFF_NUMERIC)
only if element Stiffness == STIFF_ANALYTIC
MATERIALSTIFFMETHOD -
Viscosity coefficient VISCO_ETA TO/TM

GeneralizedMaxwellViscoElastHypoMaterial

Description

The GeneralizedMaxwell viscoelastic model result in adding of up to now, maximum 2 visco-elastic Maxwell branches to the elastic material. The similar spring/damper model is shown at the figure below

Defining Maxwell viscous parameters from materials data (for each Maxwell branch):

$$ \begin{cases} \Gamma_{i} &= \frac{\mu_{i}} {2G}\\ \tau_{i} &= \frac{\eta_{i}} {\mu_{i}} \end{cases} $$

The stresses in each Maxwell branch consist in 2 effects :

  1. the relaxation of previous time step stresses in this Maxwell branch
  2. the stress modification due to strain increment ${\Delta\epsilon}_{ij}$

$$ \begin{cases} p^{1} &= p^{0} + 3K {\Delta\epsilon}_{ii} \\ \underline{s}^{1} &= \underline{s}_{E}^{1} + \underline{s}^{1}_{M1} + \underline{s}^{1}_{M2} \end{cases} $$ Stresses in each branch are computed using : $$ \begin{cases} \underline{s}_{E}^{1} &= \underline{s}_{E}^{0} + 2G {\Delta\hat{\underline{\epsilon}}} \\ \underline{s}^{1}_{M1} &= e^{(\frac{-\Delta t}{\tau_{1}})} \underline{s}^{0}_{M1} + \Gamma_{1} (1-e^{\frac{-\Delta t}{\tau_{1}}}) \frac{\tau_{1}}{\Delta t} 2G {\Delta\hat{\underline{\epsilon}}} \\ \underline{s}^{1}_{M2} &= e^{(\frac{-\Delta t}{\tau_{2}})} \underline{s}^{0}_{M2} + \Gamma_{2} (1-e^{\frac{-\Delta t}{\tau_{2}}}) \frac{\tau_{2}}{\Delta t} 2G {\Delta\hat{\underline{\epsilon}}} \\ \end{cases} $$

where $K$ and $G$ are compressibility and shear modulus, ${\Delta\underline{\epsilon}}$ is the stain increment during the time step $\Delta t$. these equations shown clearly the necessity to track history of the total stresses but also to each Maxwell branch stresses $\underline{s}^{1}_{M1}$ and $\underline{s}^{1}_{M2}$.

Parameters

Name Metafor Code Dependency
Density MASS_DENSITY -
Young's modulus ELASTIC_MODULUS TO/TM
Poisson Ratio POISSON_RATIO TO/TM
Material Stiffness
(STIFF_ANALYTIC - STIFF_NUMERIC)
only if element Stiffness == STIFF_ANALYTIC
MATERIALSTIFFMETHOD -
Number of Maxwell branches 1 (default) or 2 NBMAXWELLBRANCH -
Maxwel 1 Stiffness VISCO_MU1 -
Maxwel 1 Viscosity VISCO_ETA1 -
Maxwel 2 Stiffness VISCO_MU2 -
Maxwel 2 Viscosity VISCO_ETA2 -

model implemented based on Kaliske M, Rothert H. Formulation and implementation of three-dimensional viscoelasticity at small and finite strains. Computational Mechanics 1997;19:228-239.

EvpIsoHHypoMaterial

Description

Elasto-visco-plastic law with isotropic hardening (Yield Stress to define $ \sigma_{yield}$ ), imposed temperature.

Stresses are integrated with a radial return method. The stiffness tangent matrix is analytic and numerical.

The yield stress must verify the constraint:

$$ f=\overline{\sigma}-\sigma_{yield}=0 $$

where $ \overline{\sigma}$ is the equivalent stress computed as a function of the plastic criterion, and $ \sigma_{yield} $ is the yield stress.

Parameters

Name Metafor Code Dependency
Density MASS_DENSITY -
Young's Modulus ELASTIC_MODULUS TM
Poisson Ratio POISSON_RATIO -
Material Stiffness
(STIFF_ANALYTIC - STIFF_NUMERIC)
only if element Stiffness == STIFF_ANALYTIC
MATERIALSTIFFMETHOD -
Thermal Expansion THERM_EXPANSION TM
Number of the material law which defines the yield stress $\sigma_{yield}$ YIELD_NUM -
Evolution law of the material temperature TEMP TM
Number of the plastic criterion
(by default, it creates a VonMisesPlasticCriterion)
PLASTICCRITERION_NUM -
Objectivity Method
(Jaumann = 0, GreenNaghdi = 1)
OBJECTIVITY -
Orthotropic axis ORTHO_AX1_X -
Orthotropic axis ORTHO_AX1_Y -
Orthotropic axis ORTHO_AX1_Z -
Orthotropic axis ORTHO_AX2_X -
Orthotropic axis ORTHO_AX2_Y -
Orthotropic axis ORTHO_AX2_Z -

TmEvpIsoHHypoMaterial

Description

Thermo-elasto-visco-plastic law with nonlinear isotropic hardening (no Hill48).

Stresses are integrated with a radial return method. The stiffness tangent matrix is analytic and numerical.

The yield stress must verify the constraint:

$$ f=\overline{\sigma}-\sigma_{yield}=0 $$

where $ \overline{\sigma}$ is the equivalent stress computed as a function of the Von Mises plastic criterion, and $ \sigma_{yield} $ is the yield stress.

Careful, here the TEMP parameter is not relevant anymore.


:!: Thermomechanical calculation method :

  • When the thermal expansion changes, an average value is computed over the time step is estimated to model this thermal expansion properly.
  • If the heat capacity changes, an average value is computed to estimate properly the energy balance. An equivalent heat capacity can be used to take into account the latent heat (= heat capacity + latent heat).

Parameters

Name Metafor Code Dependency
Density MASS_DENSITY TO/TM
Young's Modulus ELASTIC_MODULUS TO/TM
Poisson Ratio POISSON_RATIO TO/TM
Material Stiffness
(STIFF_ANALYTIC - STIFF_NUMERIC)
only if element Stiffness == STIFF_ANALYTIC
MATERIALSTIFFMETHOD -
Thermal expansion THERM_EXPANSION TO/TM
Number of the material law which defines the yield stress $\sigma_{yield}$ YIELD_NUM -
Conductivity CONDUCTIVITY TO/TM
Heat capacity HEAT_CAPACITY TO/TM
Dissipated thermoelastic power fraction DISSIP_TE -
Dissipated (visco)plastic power fraction (Taylor-Quinney factor) DISSIP_TQ -

EvpMixtHHypoMaterial

Description

Elasto-visco-plastic law with nonlinear isotropic mixed hardening (no Hill48), given temperature. The size of the plastic surface is defined by the Yield Stress.

Kinematic hardening are added to have a possibly quite complex resulting kinematic hardening. A maximum of five kinematic hardening laws are allowed (whether of the same type or a different one).

Stresses are integrated with a radial return method. The stiffness tangent matrix is analytic and numerical.

The yield stress must verify the constraint:

$$ f=\overline{\sigma}\left(\boldsymbol{\sigma},\boldsymbol{\alpha}\right)-\sigma_{yield}=0 $$

where $ \overline{\sigma} $ is the quivalent stress depending in the stress tensor $ \boldsymbol{\sigma} $ and of the backstresses $ \boldsymbol{\alpha} $, and where $ \sigma_{yield} $ is the Yield Stress.

Parameters

Name Metafor Code Dependency
Density MASS_DENSITY -
Young's Modulus ELASTIC_MODULUS TM
Poisson Ratio POISSON_RATIO -
Material Stiffness
(STIFF_ANALYTIC - STIFF_NUMERIC)
only if element Stiffness == STIFF_ANALYTIC
MATERIALSTIFFMETHOD -
Thermal expansion THERM_EXPANSION TM
Number of the material law which defines the yield stress $\sigma_{yield}$ YIELD_NUM -
Number of kinematic hardening laws (maximum 5) KH_NB -
Number of kinematic hardening law 1 KH_NUM1 -
Number of kinematic hardening law 2 KH_NUM2 -
Number of kinematic hardening law 3 KH_NUM3 -
Number of kinematic hardening law 4 KH_NUM4 -
Number of kinematic hardening law 5 KH_NUM5 -
Material temperature evolution law TEMP TM

TmEvpMixtHHypoMaterial

Description

This law, a thermomechanical elasto-visco-plastic law with mixed hardening, is the thermal version of the EvpMixtHHypoMaterial law. The thermal part of the law is identical to the one of the isotropic hardening law.

Physical parameters of the kinematic hardening laws can of course depend on the temperature.


:!: Thermomechanical calculation method :

  • When the thermal expansion changes, an average value is computed over the time step is estimated to model this thermal expansion properly.
  • If the heat capacity changes, an average value is computed to estimate properly the energy balance. An equivalent heat capacity can be used to take into account the latent heat (= heat capacity + latent heat).

Parameters

Name Metafor Code Dependency
Density MASS_DENSITY TO/TM
Young's Modulus ELASTIC_MODULUS TO/TM
Poisson Ratio POISSON_RATIO TO/TM
Material Stiffness
(STIFF_ANALYTIC - STIFF_NUMERIC)
only if element Stiffness == STIFF_ANALYTIC
MATERIALSTIFFMETHOD -
Thermal Expansion THERM_EXPANSION TO/TM
Number of the material law which defines the yield stress $\sigma_{yield}$ YIELD_NUM -
Number of kinematic hardening laws (maximum 5) KH_NB -
Number of kinematic hardening law 1 KH_NUM1 -
Number of kinematic hardening law 2 KH_NUM2 -
Number of kinematic hardening law 3 KH_NUM3 -
Number of kinematic hardening law 4 KH_NUM4 -
Number of kinematic hardening law 5 KH_NUM5 -
Conductivity CONDUCTIVITY TO/TM
Heat Capacity HEAT_CAPACITY TO/TM
Dissipated thermoelastic power fraction DISSIP_TE -
Dissipated (visco)plastic power fraction (Taylor-Quinney factor) DISSIP_TQ -

EvpIsoHDamageHypoMaterial

The EvpIsoHDamageHypoMaterial class manages Gurson damage. To create such a law, the class EvpIsoHDamageHypoMaterial must be derived with a function updateElasticProperties.

Description

EvpIsoHHypoMaterial law including Gurson damage (elasto-visco-plastic law with damage and nonlinear isotropic hardening (pas de Hill48), imposed temperature.

Stresses are integrated with a radial return method. The stiffness tangent matrix is analytic and numerical.

The yield stress must verify the constraint:

$$ f=\overline{\sigma}-w\left(D,p\right)\sigma_{yield}-\sigma_{damage}=0 $$

where $ \overline{\sigma} $ is the equivalent stress computed as a function of Von Mises plasticy criterion, $ \sigma_{yield} $ is the plastic stress updated as a function of the isotropic hardening, $ \omega $ is the reduction of the yield stress due to damage, $ D $ is the damage variable $p$ the pressure and $ \sigma_{damage} $ the stress associated to material damage.

Parameters

Name Metafor Code Dependency
Density MASS_DENSITY
Young's Modulus ELASTIC_MODULUS
Poisson Ratio POISSON_RATIO
Material Stiffness
(0 : Ana - 1 : Num)
only if element Stiffness == STIFF_ANALYTIC
MATERIALSTIFFMETHOD -
Number of the material law which defines the yield stress $\sigma_{yield}$ YIELD_NUM -
Number of the damage evolution law DAMAGE_NUM
Initial damage DAMAGE_INIT

EvpIsoHDamageMoriTanakaHypoMaterial

The update of elastic properties is based on Mori-Tanaka law.

$$ G_d = \dfrac{G(1-d)}{1+d\frac{6K+12G}{9K+8G}} K_d = \dfrac{4GK(1-d)}{3Kd+4G} $$

EvpIsoHDamageJacobsHypoMaterial

if $d<0.43$

$$ G_d = G(1-d)^{3.2} K_d = G(1-d)^{3.2} $$

else

$$ G_d = Ga_0(1-d)^{2.5} K_d = Ga_0(1-d)^{2.5} $$ where $a_0=0.7$ by default

ContinuousDamageEvpIsoHHypoMaterial

Description

Elasto-visco-plastic law with continuous damage and nonlinear isotropic hardening (no Hill48), given temperature.

Stresses are integrated with a radial return method. The stiffness tangent matrix is analytic and numerical.

The yield stress must verify the constraint:

$$ f=\dfrac{\overline{\sigma}}{1-h\cdot D}-\sigma_{yield}=0 $$

where $ \overline{\sigma} $ is the equivalent stress computed as a function of Von Mises plasticy criterion, $ \sigma_{yield} $ is the yield stress, $ D $ is the damage variable updated as a function of the damage evolution law. Moreover, $h$ is the Micro-Crack Closure Effect parameter that makes the distinction of the weakening effect of damage under compressive and tensile stress states, which is defined as: $$ h = \left\{ \begin{array}{ll} \text{DAMAGE_MCCE} &\mbox{, if } \dfrac{p}{J_2}< 0.0\\ 1.0 &\mbox{, if } \dfrac{p}{J_2}\geq 0.0\\ \end{array} \right. $$

The evolution law coupled with plasticity can be integrated three ways depending on the parameter TYPE_INTEG:

  • TYPE_INTEG = 0 : iterative integration method (default)
  • TYPE_INTEG = 1 : coupled integration method
  • TYPE_INTEG = 2 : integration method following the Souza algorithm

Parameters

Name Metafor Code Dependency
Density MASS_DENSITY -
Young's Modulus ELASTIC_MODULUS TM
Poisson Ratio POISSON_RATIO -
Material Stiffness
(0 : Ana - 1 : Num)
only if element Stiffness == STIFF_ANALYTIC
MATERIALSTIFFMETHOD -
Number of the material law which defines the yield stress $\sigma_{yield}$ YIELD_NUM -
Number of the damage evolution law DAMAGE_NUM -
Initial damage DAMAGE_INIT -
Integration method TYPE_INTEG -
Micro-Crack Closure Effect parameter (=1.0 by default) DAMAGE_MCCE

ContinuousAnisoDamageEvpIsoHHypoMaterial

Description

Elasto-visco-plastic law with orthotropic damage and nonlinear isotropic hardening (no Hill48), given temperature.

Stresses are integrated with a radial return method. The stiffness tangent matrix is analytic and numerical.

The damage is a symmetric matrix $D$, the effective stress is computed from the stress tensor and from a fourth order tension $M$, which depends on $ H=(I-D)^{-1/2}$ and $ tr(D) $ : $ \tilde{\sigma}=M:\sigma$ and of $ \eta $, a parameter (double, at least equal to 1.0 - makes a material isotropic - usually taken as à 3.0 for traditional materials) (see Lemaitre, 2000 (equations 7 and 70) for information on $ M $).

The yield stress must verify the constraint:

$$ f=\overline{\sigma}_{eq}-\sigma_{yield}=0 $$

where $ \overline{\sigma}_{eq} $ is the equivalent stress computed as a function of Von Mises plasticy criterion (computed for $ \overline{\sigma} $ and not $ \sigma $), $ \sigma_{yield} $ is the yield stress.

$ H $ is the main damage variable, updated as a function of the damage evolution law.

The damage $D$ is initially diagonal.

Parameters

Name Metafor Code Dependency
Density MASS_DENSITY -
Young's Modulus ELASTIC_MODULUS TM
Poisson Ratio POISSON_RATIO -
Material Stiffness
(0 : Ana - 1 : Num)
only if element Stiffness == STIFF_ANALYTIC
MATERIALSTIFFMETHOD -
Number of the material law which defines the yield stress $\sigma_{yield}$ YIELD_NUM -
Number of the damage evolution law DAMAGE_NUM -
Initial damage (11) DAMAGE_INIT_1 -
Initial damage (22) DAMAGE_INIT_2 -
Initial damage (33) DAMAGE_INIT_3 -
“weight” of the anisotropy, $ \eta $ ETA -

TmContinuousDamageEvpIsoHHypoMaterial

Thermomechanical version of the material with continuous damage.


:!: Thermomechanical calculation method :

  • When the thermal expansion changes, an average value is computed over the time step is estimated to model this thermal expansion properly.
  • If the heat capacity changes, an average value is computed to estimate properly the energy balance. An equivalent heat capacity can be used to take into account the latent heat (= heat capacity + latent heat).

Parameters

Name Metafor Code Dependency
Density MASS_DENSITY TO/TM
Young's Modulus ELASTIC_MODULUS TO/TM
Poisson Ratio POISSON_RATIO -
Material Stiffness
(0 : Ana - 1 : Num)
only if element Stiffness == STIFF_ANALYTIC
MATERIALSTIFFMETHOD -
Number of the material law which defines the yield stress $\sigma_{yield}$ YIELD_NUM -
Number of the damage evolution law DAMAGE_NUM -
Initial damage DAMAGE_INIT -
Thermal Expansion THERM_EXPANSION TO/TM
Conductivity CONDUCTIVITY TO/TM
Heat Capacity HEAT_CAPACITY TO/TM
Dissipated thermoelastic power fraction DISSIP_TE -
Dissipated (visco)plastic power fraction (Taylor-Quinney factor) DISSIP_TQ -
doc/user/elements/volumes/iso_hypo_materials.txt · Last modified: 2022/07/14 12:41 by papeleux

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki